How to disassemble AK 47?

How to Disassemble an AK-47: A Step-by-Step Guide

The AK-47 is a popular and iconic assault rifle that has been used by military and civilian shooters alike for decades. While it’s an impressive weapon, it’s also important to know how to properly disassemble and maintain it to ensure its longevity and performance. In this article, we’ll take you through the step-by-step process of disassembling an AK-47.

Before You Start

Before you begin disassembling your AK-47, make sure you have the following:

• A clean and well-lit workspace
• A soft cloth or rag
• A small brush (optional)
• A screwdriver or punch (optional)
• A cleaning rod (optional)

Step 1: Remove the Magazine

The first step in disassembling an AK-47 is to remove the magazine. To do this, pull the magazine release lever located on the right side of the rifle, just behind the magazine well. This will allow the magazine to drop free from the rifle.

Step 2: Remove the Handguard

The next step is to remove the handguard. To do this, you’ll need to remove the screws that hold it in place. There are usually three screws on the top of the handguard that need to be removed. Once the screws are removed, you can lift the handguard off the rifle.

Step 3: Remove the Gas Tube

The gas tube is responsible for directing the gas generated by the firing of the rifle back into the receiver. To remove the gas tube, you’ll need to remove the screws that hold it in place. There are usually two screws on the top of the gas tube that need to be removed. Once the screws are removed, you can lift the gas tube off the rifle.

Step 4: Remove the Bolt Carrier Group

The bolt carrier group is the heart of the AK-47, and it’s responsible for cycling the action and chambering a new round. To remove the bolt carrier group, you’ll need to pull it back and lift it out of the receiver. You may need to use a little bit of force to get it out, but it should come out easily.

Step 5: Remove the Bolt

The bolt is the part of the bolt carrier group that actually chambers the round. To remove the bolt, you’ll need to pull it back and lift it out of the bolt carrier group. You may need to use a little bit of force to get it out, but it should come out easily.

Step 6: Remove the Firing Pin

The firing pin is the part of the bolt that strikes the primer of the cartridge to ignite it. To remove the firing pin, you’ll need to pull it out of the bolt. You may need to use a little bit of force to get it out, but it should come out easily.

Step 7: Remove the Extractor

The extractor is the part of the bolt that pulls the spent cartridge out of the chamber. To remove the extractor, you’ll need to pull it out of the bolt. You may need to use a little bit of force to get it out, but it should come out easily.

Step 8: Remove the Muzzle Brake

The muzzle brake is the part of the rifle that reduces the recoil and muzzle rise when the rifle is fired. To remove the muzzle brake, you’ll need to remove the screws that hold it in place. There are usually two screws on the top of the muzzle brake that need to be removed. Once the screws are removed, you can lift the muzzle brake off the rifle.

Step 9: Remove the Bayonet

The bayonet is the part of the rifle that allows you to attach a knife or other tool to the end of the rifle. To remove the bayonet, you’ll need to remove the screws that hold it in place. There are usually two screws on the top of the bayonet that need to be removed. Once the screws are removed, you can lift the bayonet off the rifle.

Step 10: Reassemble the Rifle

Once you’ve removed all the parts, you can start reassembling the rifle. Make sure to put each part back in its original position and tighten the screws securely. Make sure not to overtighten the screws, as this can damage the rifle.

Tips and Tricks

Here are a few tips and tricks to keep in mind when disassembling and reassembling your AK-47:

• Make sure to clean and lubricate each part as you remove it to prevent corrosion and wear.
• Use a soft cloth or rag to wipe down each part as you remove it to prevent scratches and damage.
• Use a small brush to clean out any debris or dirt that may be stuck in the rifle’s crevices.
• Use a screwdriver or punch to remove any stubborn parts that may be stuck.
• Use a cleaning rod to clean out the rifle’s barrel and chamber.

Conclusion

Disassembling an AK-47 can seem intimidating at first, but with the right steps and precautions, it’s a relatively simple process. By following the steps outlined in this article, you should be able to disassemble and reassemble your AK-47 with ease. Remember to always handle the rifle with care and follow proper safety procedures when disassembling and reassembling it.

Table: AK-47 Disassembly Steps

Bullets: Important Points to Remember

• Always handle the rifle with care and follow proper safety procedures when disassembling and reassembling it.
• Make sure to clean and lubricate each part as you remove it to prevent corrosion and wear.
• Use a soft cloth or rag to wipe down each part as you remove it to prevent scratches and damage.
• Use a small brush to clean out any debris or dirt that may be stuck in the rifle’s crevices.
• Use a screwdriver or punch to remove any stubborn parts that may be stuck.
• Use a cleaning rod to clean out the rifle’s barrel and chamber.